Articles from Vadzo Imaging

The Bolt-1335MRS is an Onsemi AR1335 13MP Monochrome MIPI Camera, and Vadzo is positioning it with the Rockchip RV1126 for point-of-care diagnostic imaging devices. Many diagnostic readers do not need color. They need to measure how bright a line, a spot, or a well is, and to measure it repeatably in a small, battery-powered instrument. A monochrome sensor has no color filter array, so more light reaches every pixel, and its 13 million pixels let software average thousands of them across a test line, which lowers random noise sharply. The Bolt-1335MRS pairs that sensor with an on-board ISP that applies auto-exposure, and it sends frames over MIPI CSI-2 directly to the processor. As a 13MP Monochrome RV1126 MIPI Camera, it supports on-device analysis, and it also works with Raspberry Pi and NVIDIA Jetson Orin Nano, Orin NX, and AGX Orin. Designed for handheld and portable diagnostic devices, it supplies clean, consistent grayscale images.

The Armor-821CRS is an Onsemi AR0821 8MP HDR GMSL2 Camera, and Vadzo Imaging is launching it for high-resolution embedded vision. Vehicles, robots, and large machines often need a camera that sits far from the computer that reads it, in an environment full of electrical noise, vibration, and heat. A flat MIPI cable reaches only a short distance, and USB and Ethernet add cost and latency. GMSL2 is a serializer and deserializer link that carries high-speed video and control over a single coaxial or twisted pair cable, and the Armor-821CRS uses it to stream 4K video at 30 frames per second over a cable up to 15 meters long. HDR keeps bright and dark regions readable, and an on-board ISP applies auto exposure and auto white balance. As a 4K HDR GMSL2 Camera, an 8MP GMSL2 Camera Module, and an Embedded Vision GMSL2 Camera, it integrates several units with NVIDIA Jetson Orin NX and AGX Orin, supplying clean frames to the computer.

The Falcon-234MGS is a 2MP Onsemi AR0234 Mono Global Shutter USB Camera, and Vadzo is positioning it for motion-accurate aerial inspection and UAV navigation. Software that navigates an aircraft or inspects a structure from the air cares about brightness and geometry, not color. A monochrome sensor collects more light per pixel because it has no color filter array, and it needs no interpolation, so every pixel is a real measurement. A global shutter exposes every pixel at the same instant, so edges stay straight while the aircraft vibrates and moves. The Falcon-234MGS streams Full HD at 60 frames per second in Y8 format, along with 720p at 60 and VGA at 90, and an onboard ISP applies anti-flicker for 50Hz and 60Hz lighting. As a 2MP Full HD Mono USB Camera and an AR0234 Global Shutter Mono USB Camera, it also captures BMP and JPEG stills. Designed for UAV makers, it supplies compact, accurate frames to the flight computer.

The Bolt-830CRS is an 8MP HDR MIPI CSI-2 Camera built on the Onsemi AR0830 sensor, and Vadzo has validated it with the Rockchip RK3588 for reduced power monitoring. A monitoring camera spends most of its time watching an empty scene and a small share of it recording something that matters. Streaming at full resolution all day wastes power on the empty hours, and waking slowly loses the event. The Bolt-830CRS combines wake on motion with context switching, which lets the sensor move between a low-power watch configuration and a full HDR capture configuration without reloading its settings and restarting the stream. An on-board ISP applies auto exposure and auto white balance, and the module sends Full HD or higher video over MIPI CSI-2 straight to the processor. As an 8MP WOM MIPI Camera and an 8MP Low Power HDR MIPI Camera, it also supports Raspberry Pi and NVIDIA Jetson Orin. Designed for always-on monitoring, it spends power only when there is something to see.

The Innowave-2020CRS is an Onsemi 20MP AR2020 Color GigE Wi-Fi camera, and Vadzo Imaging has validated its near-infrared response at 850nm and 940nm. A camera that works at night has to do two opposite things. By day it must block infrared light so that colors look right, and by night it must let infrared light through so that an infrared illuminator can light the scene without being seen or without disturbing anyone. The Innowave-2020CRS handles both with an M12 lens mount and an electromechanical IR cut filter. As a 20MP NIR GigE Wi-Fi camera, it keeps 20MP detail in the near-infrared band, and it adds Gigabit Ethernet and dual-band Wi-Fi, ONVIF, IEEE 1588 PTP, onboard storage, unicast and multicast streaming, and an onboard dewarping engine for lenses up to 200 DFOV. High dynamic range up to 100 dB helps with scenes that mix bright and dark regions. Designed for surveillance, medical, automation, and retail systems, it brings day and night imaging to flexible networks.

The Innowave-1335CRA is a 13MP Autofocus GigE WiFi Camera built on the Onsemi AR1335 sensor, and Vadzo Imaging is introducing it for embedded vision engineers and system integrators. Many installations need one camera to do several jobs. It should reach the network over a cable or over Wi-Fi, keep recording when the link drops, follow subjects at different distances, and show a wide scene and a close detail from the same 13MP frame. The Innowave-1335CRA carries Gigabit Ethernet and dual-band Wi-Fi in one camera, with ONVIF compliance, IEEE 1588 PTP, onboard storage, and unicast and multicast streaming. A voice coil motor autofocus covers 100mm to infinity, ROI based autofocus and exposure follow a chosen region, digital pan, tilt, and zoom navigate the frame, and iHDR handles mixed lighting. As a 4K Autofocus GigE WIFI Camera and a 13MP Autofocus Ethernet WiFi Camera, it brings flexible networking to detailed imaging.

The Falcon-521CRS is an Onsemi AR0521 Color 5MP Low-Noise USB 3.2 Gen1 Camera, and Vadzo has validated its on-board ISP for on-camera image processing. A sensor produces raw data, and raw data is not a picture. Turning it into one takes demosaicing, color and contrast correction, gamma, noise reduction, lens correction, exposure control, and white balance, and where that work happens shapes cost, consistency, and effort. As an On-Camera Image Processing USB Camera and an Onboard Image Processing Camera, the Falcon-521CRS performs those steps inside the module with a high-performance ISP, and it exposes tuning controls through the standard UVC interface. It adds anti-flicker for 50Hz and 60Hz lighting, streams YUYV or MJPEG video, and captures BMP or JPEG stills. Large 2.2-micron pixels keep noise low before processing begins. Designed for security, retail, and medical device makers, it delivers a finished, consistent image from a single USB cable.

The Merlin-234CGS is a 2MP Color Global Shutter USB 2.0 Camera built on the Onsemi AR0234 sensor, and Vadzo is positioning it for motion-accurate UAV imaging. A camera on an aircraft vibrates, moves, and sees the ground rush past, and any one of those can bend straight lines in a picture. A global shutter exposes every pixel at the same instant, so the geometry stays true. The Merlin-234CGS adds a high-performance ISP with ROI based auto exposure, auto white balance, and on-board dewarping, which straightens the image from a wide-angle lens before it leaves the camera. It connects over USB 2.0 with UVC compliance, a common interface on the small computers that fly with a UAV, and it offers YUV422, H.264, and MJPEG video formats so that the stream fits the link. Designed for UAV imaging, mapping, and inspection payloads, it supplies undistorted, correctly exposed frames to the flight computer.

The Bolt-234CGH is a 2MP Onsemi AR0234 Global Shutter Autofocus MIPI Camera, and Vadzo has validated it with the Rockchip RV1126 for motion-accurate drone imaging. A drone camera has to stay accurate while the aircraft vibrates, banks, and flies at speed. A global shutter exposes every pixel at the same instant, so edges stay straight and the geometry that navigation and obstacle detection depend on stays true. A voice coil motor autofocus lets the same camera serve close inspection and landing as well as distant views. An on-board ISP finishes the image, and the module sends Full HD video over MIPI CSI-2 directly to the processor, which saves the weight and power of a USB controller. As a 2MP Global Shutter MIPI Camera and a 2MP Rockchip RV1126 MIPI Camera, it also supports Raspberry Pi and NVIDIA Jetson Orin Nano, Orin NX, and AGX Orin. Designed for drone and UAV makers, it supplies undistorted, correctly exposed frames to the flight computer.

The Falcon-830CRH is an 8MP 4K HDR Autofocus USB 3.2 Gen 1 Camera built on the Onsemi HyperLux LP AR0830 sensor, and Vadzo has validated its LI-HDR and eDR modes. Camera units at kiosks, store entrances, and security points face two problems at once. The people in front of them stand at different distances, so focus must follow, and the light is rarely even, with bright doorways and dark interiors in the same frame. The Falcon-830CRH answers both with a voice coil motor autofocus on an M12 standard lens and two dynamic range modes, line interleaved HDR for extreme contrast and enhanced dynamic range for moderate contrast. Wake on motion lets it rest between events, and an on-board high-performance ISP applies auto exposure and auto white balance. As a 4K LI-HDR eDR Camera and an 8MP VCM Autofocus USB Camera, it connects over a standard USB 3.2 Gen1 cable. Designed for security, retail, and kiosk systems, it keeps subjects sharp and correctly exposed.

The Innowave-2020CRS is a 20MP Color GigE WiFi Camera built on the Onsemi AR2020 sensor, and Vadzo Imaging is introducing it for embedded vision engineers and system integrators. Real installations rarely suit a single connection type. A camera on a pole may have a cable, a camera on a moving cart may not, and a temporary setup may need to run before any cable is pulled. The Innowave-2020CRS carries both Gigabit Ethernet and WiFi in one camera, so the same unit can be commissioned wirelessly and then run on a cable, or fall back to wireless if the cable fails. It complies with ONVIF, synchronizes clocks with IEEE 1588 PTP, records to onboard storage, and streams unicast or multicast. An onboard dewarping engine corrects lenses up to 200 DFOV, and an M12 lens mount with an electromechanical IR cut filter handles day and night. Designed for smart city, telematics, kiosk, medical, security, robotics, and retail systems, this 20MP ONVIF GigE WiFi Camera and 20MP Onboard Dewarping Engine Camera bring 20MP detail to flexible networks.

The Bolt-521CRS is a 5MP Low-Noise MIPI Camera built on the Onsemi AR0521 sensor, and Vadzo is positioning it with NVIDIA Jetson AGX Orin for medical and life science imaging. Medical and laboratory instruments image small, dim, and often strobe lit subjects, and they depend on clean color and consistent exposure. The Bolt-521CRS pairs large 2.2 micron pixels with an on board ISP, so the frame arrives with low noise and finished color. Its sensor also supports Global Reset Release, a mode that starts exposure on every row at the same moment, which lets a rolling shutter sensor work with a flash or a controlled light source and avoids much of the usual skew. The module supports NVIDIA Jetson Orin Nano, Orin NX, and AGX Orin through 2 lane and 4 lane adapter boards. Designed for instrument makers building microscopes, ophthalmic and intraoral devices, and laboratory systems, this 5MP Jetson AGX Orin MIPI Camera and 5MP GRR MIPI Camera supplies clean, correctly colored images to the Jetson platform of their choice.

The Falcon-234CGH is a 2MP onsemi AR0234 Color Global Shutter Autofocus USB Camera, and Vadzo is positioning it for accurate barcode reading in kiosks and digital signage systems. A barcode reader fails for simple reasons. The code is out of focus; it blurs because the user's hand or phone is moving, it is washed out by glare from a phone screen, or it covers too few pixels to decode. The Falcon-234CGH addresses each one. A voice coil motor autofocus lens brings the code into focus at whatever distance the user holds it, a global shutter freezes motion without skew, and an on-board ISP applies auto exposure, auto white balance, and denoising before the frame leaves the camera. The lens is a 74 DFOV S-Mount design, and the module connects over USB 3.2 Gen1 with UVC compliance. Designed for kiosk and digital signage makers, this 2MP Color Global Shutter Autofocus USB Camera supplies sharp, correctly exposed frames to the decoding software, and it reads both printed codes and codes on phone screens.

The Innova-234CGE is a 2MP Color GigE Camera built on the Onsemi AR0234 sensor, and Vadzo is positioning it for reliable day and night video recording. Recording that never stops asks more of a camera than a good picture. The stream must stay up for months, the bitrate must fit the network and the storage, the image must stay usable as daylight fades, and installation must be simple enough to repeat across many positions. As a 2MP Day Night GigE Camera and a 2MP Color Day Night GigE Camera, the Innova-234CGE answers those needs with a global shutter, an on-board ISP, ONVIF compliance, and PTP synchronization. It streams 1080p, 720p, and VGA at up to 60 frames per second, and it carries video, control, and power over a single Ethernet cable. Designed for smart surveillance, patient monitoring, and mobile robot systems, it gives integrators a color GigE camera that is built to keep recording.

The Falcon-521CRS is an AR0521 Color USB 3.2 Gen 1 Camera built on the Onsemi AR0521 sensor, and Vadzo is positioning it for pedestrian safety surveillance. Watching a crosswalk is harder than it looks. People cross at dusk and in the dark, headlights sweep across the scene, street lamps create bright spots, and the pedestrians who matter most are often the darkest objects in the frame. A noisy camera hides them, and an exposure set by the headlights loses them. The Falcon-521CRS pairs large 2.2 micron pixels with low-noise imaging, a high-performance ISP, and ROI based auto exposure that meters on the crosswalk instead of the lights. It streams Full HD and 5MP color video in YUYV or MJPEG over a standard USB 3.2 Gen 1 cable and complies with UVC, so it opens without a custom driver. Designed for integrators building pedestrian safety monitoring and analytics, it supplies a clean, correctly exposed picture of the people at the crossing.

The Bolt-1335CRA is an AR1335 Color Autofocus MIPI CSI-2 Camera built on the Onsemi AR1335 sensor, and Vadzo is positioning it with the RK3588 Rockchip processor for pathology imaging in medical and life science applications. Pathology devices judge tissue by color and detail, and they photograph specimens, slides, and labels that sit at different heights and distances. A fixed lens must be refocused by hand each time, and a camera with weak color processing changes what a reviewer sees. As a 13MP Autofocus MIPI CSI-2 Camera, the Bolt-1335CRA focuses automatically from 100mm to infinity with a voice coil motor, finishes the image in an on-board ISP, and connects through 2-lane or 4-lane adapter boards. It supports the RK3588 and the NVIDIA Jetson Orin Nano, Orin NX, and AGX Orin platforms, so an instrument maker can choose compute separately from the camera. Designed for device makers building pathology and life science instruments, it supplies sharp, consistently colored images without manual focus.

The Falcon-2020CRS is a 20MP Color USB 3.2 Gen 1 Camera built on the Onsemi AR2020 sensor, and Vadzo is positioning it for counter-drone applications. A small drone at long range occupies very few pixels, flies against a bright sky, and may arrive at dusk or after dark, so the camera that watches it is limited by resolution, contrast, and light all at once. The Falcon-2020CRS puts more pixels on a distant target, keeps excellent response in the near infrared at 850nm and 940nm for illuminated night work, and offers eDR and HDR modes for bright skies and dark subjects. Wake on motion lets a remote node rest between events. The module connects over a standard USB 3.2 Gen 1 cable and carries an S-Mount lens holder. Designed for integrators building counter-drone systems, it supplies the visual layer that confirms and tracks what other sensors report.

The Innova-521CRS is a 5MP Color Rolling Shutter GigE Camera built on the Onsemi AR0521 sensor, and Vadzo is positioning it for continuous day and night video monitoring. Monitoring sites ask a camera to cover a wide area, to see in dim light, to cope with headlights and bright windows, and to keep working for months. A 5MP frame covers more ground than a 2MP frame, large 2.2 micron pixels gather light after dark, and HDR keeps bright and dark regions readable in the same picture. As a 5MP Ethernet Camera and an AR0521 Color Ethernet Camera, the Innova-521CRS connects over a single network cable, complies with ONVIF so standard video software can use it, supports PTP synchronization so several units share a time base, and finishes the picture in an onboard ISP. For monitoring that needs sharp stills of moving subjects, the sensor can also work with an external mechanical shutter. Designed for integrators building around-the-clock monitoring, it brings coverage, sensitivity, and standards support together.

The Bolt-821CRS is a 4K HDR MIPI CSI-2 Camera built on the Onsemi AR0821 sensor, and Vadzo is positioning it for enhanced cargo visibility in telematics applications. A cargo space is one of the hardest scenes a vehicle camera faces. The interior is dark, the open door or the window behind it is bright, and the lighting changes every time the vehicle moves from a warehouse dock to a sunlit road. As an 8MP Telematics HDR MIPI Camera and a 4K HDR MIPI Camera with 120+dB of dynamic range, the Bolt-821CRS keeps the load and the opening readable in the same frame. An on-board image signal processor applies auto exposure and auto white balance inside the module, and anti-flicker settings handle 50Hz and 60Hz lighting. It supports Raspberry Pi and NVIDIA Jetson Orin Nano, Orin NX, and AGX Orin platforms through 2-lane and 4-lane adapter boards. Designed for fleet and telematics systems, this Cargo Visibility HDR MIPI Camera gives vehicle gateways a clear view of what is on-board.

The Falcon-830CRS is an 8MP Color USB Camera built on the Onsemi HyperLux LP AR0830 sensor, and Vadzo has validated its super-low-power performance for power-efficient embedded vision. Battery-powered and always-on devices cannot afford a camera that streams all day to catch a few seconds of activity. They need a module that idles at very low power, wakes when something moves, and then captures a frame that holds detail in both bright and dark regions. As a 4K Super Low Power USB Camera, the Falcon-830CRS combines a super low power mode with wake on motion, and two dynamic range modes, line interleaved HDR and enhanced dynamic range, for scenes of different contrast. Auto exposure and auto white balance keep the picture usable from the first frame. As an 8MP Low Power USB Camera and a 4K Color USB 3.2 Gen 1 Camera, it connects over a standard cable. Designed for smart security, retail in-store, kiosk, and drone systems, the module helps designers spend power only when there is something to see.

The Bolt-234CGS is a 2MP Color MIPI CSI-2 Camera built on the Onsemi AR0234 sensor, and Vadzo has validated its compatibility with NVIDIA Jetson AGX Orin. Jetson AGX Orin is a platform for multi-camera robots, retail systems, and surveillance nodes, and the camera modules attached to it decide how well that compute is used. Two choices matter most. A global shutter exposes every pixel at the same instant, so a moving robot, a passing shopper, or a vehicle appears undistorted. An on-board image signal processor finishes the image inside the module, so the Jetson receives a processed YUV image and its own ISP does not need to be tuned for the sensor. As a 2MP Global Shutter MIPI Camera and a 2MP AGX Orin MIPI Camera, the Bolt-234CGS delivers Full HD at up to 60 frames per second, with auto exposure and auto white balance applied in the module. Designed for warehouse robotics, smart surveillance, and retail analytics and automation, it gives AGX Orin systems consistent color and distortion-free frames.

The Falcon-821CRS is an 8MP AR0821 4K HDR USB 3.2 Gen 1 Camera, and Vadzo has validated it for 120+dB high dynamic range. Real scenes are rarely evenly lit. A vehicle leaves a tunnel into direct sun, a warehouse door opens onto a bright yard, a storefront window floods a lobby with daylight, and a robot turns from a dark aisle toward a lit dock. Each of these scenes can span 120dB or more from the darkest shadow to the brightest highlight, far more than a single exposure records. The Falcon-821CRS captures that span on the sensor and then finishes the image with an on-board image signal processor that performs debayering, color correction, gamma correction, denoising, auto exposure, and auto white balance before the frame reaches the USB port. As an HDR USB 3.2 Gen1 Camera and a High Contrast Imaging USB Camera, it delivers a usable image straight to the host. Designed for telematics, surveillance, robotics, and retail automation, the module keeps both highlights and shadows in a single frame.

The Bolt-544CRS is a 5MP low-power MIPI Camera built on the Onsemi HyperLux LP AR0544 sensor, and Vadzo has validated it on the Rockchip RV1126 for embedded vision applications. The RV1126 is a favorite for compact smart camera products because it combines an image signal processor, a neural processing unit, and a video encoder in a low-power chip, and the camera attached to it decides how much of that efficiency survives in the finished device. The Bolt-544CRS pairs wake-on-motion with low power consumption, so a device can sleep through quiet hours and wake only when something moves. Line interleaved HDR (LI-HDR) and enhanced dynamic range (eDR) modes handle scenes that mix bright and dark regions, and auto exposure and auto white balance keep the image consistent. As a 5MP Wake-on-Motion MIPI Camera, a Low Power Embedded MIPI Camera, and an RV1126 5MP Camera, it connects through standard MIPI CSI-2. Designed for automation and robotics, smart security, retail automation, telematics, and kiosk devices, it gives low-power designs a color image with 5MP of detail.

The Innova-1335CRA is a 13MP Color Autofocus ONVIF GigE Camera built on the Onsemi AR1335 sensor, and Vadzo has validated its ROI based auto exposure and autofocus for precise imaging. A camera that meters and focuses on the whole frame serves the average of the scene, and the average is rarely the subject. A bright kiosk screen, a sunlit window, a specimen on a dark stage, or a shelf edge in a busy aisle can pull exposure and focus away from the region that matters. With ROI based AE and AF, the camera measures exposure and finds focus inside a region chosen by the integrator. As a 13MP ONVIF Gigabit Ethernet Camera and a 4K Autofocus ONVIF Ethernet Camera, it adds Digital PTZ, iHDR, an on-board ISP, and PTP synchronization, and it carries power and data over one PoE cable. Designed for pathology devices, kiosks and signage, smart city systems, and retail analytics, the Innova-1335CRA gives networked vision a sharp, well-exposed picture where it counts.

The Innova-1335CRA is a 13MP 4K GigE camera powered by the onsemi AR1335 image sensor. Vadzo Imaging has validated its NIR cut filter for maintaining natural color reproduction by blocking unwanted near-infrared light, while its voice coil motor (VCM)-based autofocus supports focusing distances from 100 mm to infinity. These capabilities make the camera suitable for systems that require consistent color imaging and flexible focus control across varying object distances. Additional features, including onboard image signal processing, ONVIF compliance, and Precision Time Protocol (PTP) synchronization, support integration into networked imaging systems and multi-camera setups. The camera is suited to pathology devices, kiosks and digital signage, smart city systems, and retail analytics.

The Bolt-521CRS is a 5MP Color MIPI CSI-2 Camera built on the Onsemi AR0521 sensor, and Vadzo has validated its low-noise imaging on the RK3588 Rockchip processor. Noise decides how useful an embedded image is. It hides detail in dim scenes, confuses detection models, and inflates the bitrate of recorded video. Where that noise gets controlled matters as much as how much of it there is, because a raw sensor module leaves denoising, color processing, and tuning to the host, and the result depends on how well the host was tuned. The Bolt-521CRS takes a different route. Large 2.2-micron pixels gather more light, and an on-board image signal processor applies denoising, color correction, and auto exposure inside the module, so the host receives a finished YUV image. As a Low Noise Embedded Camera, it delivers Full HD at up to 60 frames per second and 5MP at up to 30 frames per second. Designed for smart surveillance, warehouse robotics, and medical and life science devices, this RK3588 Compatible MIPI Camera gives embedded teams a clean, consistent image on Rockchip, Raspberry Pi, and NVIDIA platforms.

The Innova-234CGE is a 2MP Global Shutter GigE Camera built on the Onsemi AR0234 sensor, and Vadzo has validated its ONVIF compliance for smart surveillance. Surveillance systems rarely come from one vendor, so a camera must speak a common language to join an existing video management platform. This Smart Surveillance GigE Camera is compliant with ONVIF Profile S for streaming, Profile T for events, and Profile G for recording, and an on-board image signal processor encodes H.264 and H.265 video at up to 60 frames per second. The global shutter exposes every pixel at the same instant, so faces, vehicles, and pedestrians in motion stay undistorted. An IR LED board with IR cut filter control supports day and night recording, and Power over Ethernet carries data and power on a single cable. Designed for facial recognition, day and night video recording, smart parking, and pedestrian safety, this 2MP ONVIF Global Shutter Ethernet Camera gives integrators a standards-based way to add accurate motion capture to a surveillance network.

The Falcon-2020CRH is a 20MP Autofocus NIR Color Camera based on the onsemi HyperLux LP AR2020 sensor, validated for near-infrared response at 850nm and 940nm. Combining high-resolution color imaging with VCM-based autofocus, the camera supports NIR imaging applications that require fine image detail and focus adjustment across varying working distances. With USB 3.2 Gen 1 connectivity, resolutions up to 20MP, and 4K video output at up to 30 fps in MJPEG, the Falcon-2020CRH provides a High Resolution NIR Camera platform for OEMs developing smart surveillance, machine vision, biometric imaging, and other embedded vision systems. Its autofocus capability and USB interface make it a flexible NIR Autofocus USB Camera for applications using 850nm or 940nm illumination.

Built for smart surveillance, security monitoring, and machine vision applications that operate in challenging lighting conditions rather than controlled studio environments, this camera pairs the Sony IMX662 sensor's genuine low-light sensitivity and enhanced NIR response with HDR handling over low-latency USB 2.0 streaming, giving surveillance system integrators and security equipment manufacturers professional imaging quality regardless of ambient light conditions or infrared illumination requirements.

The Bolt-830MRS is an 8MP AR0830 Monochrome MIPI Camera built on the Onsemi HyperLux LP sensor, and Vadzo has validated its 100+dB dynamic range and its wake-on-motion function for always-on devices. Battery-powered sensors spend most of their lives waiting, and the host processor is usually the largest consumer of energy while it waits. A low-power MIPI Camera Module that can watch for motion by itself lets the processor sleep until something actually happens. Dynamic range matters at the same moment, because a device watching a scene with bright sky and deep shadow must notice motion in either region. Monochrome adds sensitivity and lighter processing, since no color filter array sits over the pixels. The Bolt-830MRS combines these properties with a MIPI CSI-2 interface in a module for security, vehicle, kiosk, and industrial products. Output reaches 4K, and the module is designed to keep average power low.

The Merlin-662CRS is a 2MP color rolling-shutter USB 2.0 camera built on the Sony STARVIS 2 IMX662 sensor, with validated NIR sensitivity for illuminated low-light vision. In environments where ambient light is limited or inconsistent, controlled near-infrared illumination can help vision systems maintain usable image capture. As a Sony IMX662 1080P HDR USB Camera, the Merlin-662CRS combines NIR sensitivity with ultra-low-light imaging and HDR performance for challenging lighting conditions. For OEMs developing embedded vision systems, the camera provides a UVC-compliant USB 2.0 interface for straightforward integration with Windows, Linux, and Android platforms. Its combination of NIR sensitivity, low-light imaging, HDR, and compact USB connectivity makes it suitable for systems requiring reliable color imaging under controlled illumination, including smart surveillance, facial recognition, robotics, AGVs, and smart-city devices.

The Falcon-900MGS is a 3MP monochrome global shutter USB camera built on the Sony IMX900 sensor and validated specifically for Quad HDR, a four-exposure fusion technique that resolves scenes containing both extremely bright and extremely dark regions within the same frame. A standard dynamic range sensor exposed for a bright region loses all detail in shadow, and exposed for shadow detail instead blows out the bright region entirely, a limitation that a simple two-exposure HDR technique only partially addresses in scenes with truly extreme contrast such as a backlit doorway or a reflective industrial surface next to a dark recess. The Falcon-900MGS combines four separate exposures into a single output frame, extending usable dynamic range well beyond what two-exposure HDR achieves, while its global shutter architecture holds this fusion process free of the motion artifacts that a rolling shutter or sequentially captured multi-frame technique would introduce. Output modes span full 3MP capture down to 1080p and 720p. Designed for OEMs building security and surveillance systems, industrial inspection, and robotics vision platforms, the Falcon-900MGS gives high-contrast scenes the dynamic range that a standard or even a simple dual-exposure sensor cannot resolve.

The Merlin-290CRS is a 2MP color rolling shutter USB camera built on the Sony IMX290 sensor and tuned around a high-performance image signal processor specifically for security and surveillance workloads. Raw sensor sensitivity only tells part of the low-light story: the image signal processor decides whether a dim scene becomes a clean, identifiable frame or a noisy, unusable one. Vadzo tunes the Merlin-290CRS's noise reduction, exposure control, and color reproduction specifically for surveillance conditions rather than shipping the sensor manufacturer's generic reference settings. Native USB 2.0 UVC connectivity means the camera enumerates without proprietary drivers on any standard host platform. Designed for OEMs and system integrators building smart security, perimeter, CCTV, and access control products, the Merlin-290CRS gives surveillance deployments the image quality that a well-tuned processing pipeline delivers, not just the raw specification sheet a sensor datasheet promises.

The Falcon-1335MRH is a 13MP monochrome rolling shutter USB 3.2 Gen1 camera built on the Onsemi AR1335 sensor with VCM autofocus and validated specifically for ROI based auto exposure in medical and life sciences imaging. In microscopy, pathology, and diagnostic setups, the specimen usually fills only part of the frame, while bright slide margins, light source edges, and glass glare fill the rest. A camera that meter's exposure across the entire frame sets brightness for that surrounding clutter instead of the region a technician or algorithm needs to read. The Falcon-1335MRH meters exposure inside a defined region of interest, so brightness follows the specimen rather than its surroundings. Paired with VCM autofocus and an M12 lens mount, the module gives equipment manufacturers sharp, consistently exposed monochrome frames at full 13MP resolution. Output modes span full 13MP capture down to 4K, 1080p, and 720p. Designed for OEMs building microscopy, pathology, diagnostic, and point-of-care platforms, the Falcon-1335MRH keeps exposure tied to the part of the image that matters.

The Falcon-830CRH is an 8MP color rolling shutter USB 3.2 Gen 1 camera built on the Onsemi HyperLux LP AR0830 sensor, and Vadzo has validated its M12 lens-based VCM autofocus assembly as one optical and mechanical system. An M12 lens gives OEMs a standard, widely available family of focal lengths and fields of view, while a voice coil motor moves that lens to hold focus as the subject distance changes. Joining the two is harder than it sounds. The lens mass must suit the actuator, the travel must cover the intended focus range, the lens must sit square to the sensor, and the optics must resolve the detail that an 8MP sensor can record. Vadzo checks those factors together instead of treating the lens and the actuator as separate purchases. With HDR imaging, UVC compliance, and 4K output, the module serves barcode, inspection, kiosk, robotics, and aerial platforms that need both optical choice and reliable focus.

The Innova-662CRS is a 2MP Gigabit Ethernet Camera with high SNR based on the Sony STARVIS 2 IMX662 sensor, designed to deliver cleaner image capture in low-light and changing illumination conditions. Its high signal-to-noise ratio helps preserve useful image detail as available light decreases, supporting continuous day-and-night imaging across surveillance, traffic monitoring, and other outdoor applications. With Gigabit Ethernet, Power over Ethernet, and ONVIF Profiles S, T, and G support, the camera provides an IMX662 Ethernet Camera platform that can integrate with compatible video management, streaming, and recording systems for 24/7 networked vision deployments.

The Bolt-1335CRS is a 13MP color rolling shutter MIPI CSI-2 camera built on the Onsemi AR1335 sensor with factory-set fixed-focus optics, and Vadzo has validated it for the Rockchip RV1126 processor. Autofocus is often treated as the default upgrade, but many edge AI devices work at a known distance and gain little from a moving lens. A locked lens has no actuator to wear, no focus search to disturb the video, and no variation from one frame to the next, which makes the image easier for an inference model to trust. The challenge shifts to getting the focus right at the factory and keeping it there. Vadzo sets and locks the focus for the intended working distance and confirms that the module streams cleanly through the RV1126 camera interface. Output modes span full 13MP capture down to 4K, 1080p, and 720p. Designed for OEMs building edge AI, robotics, industrial, security, and kiosk devices on RV1126, the Bolt-1335CRS gives fixed-distance applications sharp, repeatable images without the cost and complexity of a moving lens.

The Falcon-900MGS is a 3MP Monochrome Global Shutter USB Camera based on the Sony Pregius S IMX900 sensor, validated with automatic exposure control for consistent image capture as lighting conditions change. Its global shutter architecture enables accurate imaging of moving subjects, while real-time exposure adjustment helps maintain usable image quality across varying illumination. With USB connectivity and support for multiple output resolutions, the Falcon-900MGS provides OEMs and system integrators with an IMX900 Global Shutter USB Camera platform for industrial inspection, robotics, sorting, and warehouse vision applications.

The Innova-662CRE is a 2MP Color HDR GigE Camera based on the Sony STARVIS 2 IMX662 sensor, delivering 1080p HDR imaging with enhanced low-light and near-infrared sensitivity for demanding day-and-night applications. With Gigabit Ethernet, Power over Ethernet, and support for ONVIF Profiles S, T, and G, the camera provides standardized network connectivity for integration with compatible video management, streaming, and recording systems. Designed for OEMs and system integrators, the Innova-662CRE provides a Full HD HDR Ethernet Camera platform for smart traffic monitoring, surveillance, intelligent transportation, and other applications requiring reliable color imaging across changing lighting conditions.

The Falcon-830CRH is a 4K Autofocus USB Camera based on the onsemi HyperLux LP AR0830 sensor, combining 8MP HDR imaging with an M12 voice coil motor autofocus lens. The autofocus capability enables the camera to maintain sharp image capture across changing working distances, while HDR imaging preserves detail across bright and dark regions of the scene. With USB 3.2 Gen 1 connectivity and multiple output modes including 4K, 1080p, and 720p, the camera provides OEMs and system integrators with an M12 VCM Autofocus USB Camera platform for barcode scanning, document imaging, kiosks, machine vision, and other applications requiring high-resolution autofocus imaging.

The Merlin-662CR is a 2MP Sony HDR USB Camera built around the Sony STARVIS 2 IMX662 sensor, delivering 1080p HDR imaging with enhanced low-light performance for retail analytics applications. The combination of HDR and the IMX662's low-light sensitivity helps preserve usable image detail across challenging retail environments, from brightly lit storefronts and display areas to dimmer aisles and changing ambient conditions. With USB connectivity and UVC compatibility, the camera provides retailers, analytics providers, and OEM system integrators with a Sony STARVIS USB Camera platform for customer behavior analysis, occupancy monitoring, queue analytics, and other vision-based retail applications.

The Bolt-1335CRA is a 13MP Color Autofocus MIPI Camera based on the onsemi AR1335 sensor, validated for integration with the NVIDIA Jetson AGX Orin platform. Its autofocus capability enables the camera to maintain sharp image capture across changing object distances, while the 13MP color sensor provides the resolution required for detailed vision applications. With a MIPI CSI-2 interface designed for direct integration with the Jetson AGX Orin's camera pipeline, the Bolt-1335CRA provides OEMs and system integrators with a validated Jetson Camera for AGX Orin for robotics, machine vision, intelligent inspection, and other edge AI applications requiring high-resolution autofocus imaging.

The Innova-821CRS is an AR0821 HDR Gigabit Ethernet Camera built around the onsemi AR0821 sensor, delivering 8MP 4K resolution and HDR imaging for industrial inspection applications. HDR imaging helps preserve detail across bright highlights and darker areas within the same inspection scene, supporting consistent imaging of parts with varying surface reflectivity, finishes, and illumination. Gigabit Ethernet connectivity, ONVIF Profiles S, T, G, and M, RTSP streaming, Power over Ethernet, and IEEE 1588 PTP provide a standardized network interface for integrating the camera into industrial vision and multi-camera inspection systems. Designed for OEMs and system integrators developing assembly, packaging, quality inspection, sorting, and metrology systems, the Innova-821CRS provides an 8MP GigE Camera for Industrial Inspection where high resolution, HDR imaging, and network integration are required.

The Falcon-1335MRH is a 13MP Monochrome USB Camera based on the onsemi AR1335 sensor, validated with autofocus for high-resolution imaging across varying working distances. Its monochrome sensor architecture provides strong contrast for applications such as barcode reading, document imaging, inspection, and machine vision, while the autofocus capability allows the camera to maintain sharp detail as the distance to the target changes. With USB 3.2 Gen 1 connectivity and UVC support, the camera provides OEMs and system integrators with a flexible Mono Autofocus USB Camera platform for applications where both high resolution and reliable focus are required.

The Merlin-662CRS is a 2MP IMX662 USB Camera built around the Sony STARVIS 2 IMX662 sensor, validated for ultra-low-light imaging in challenging lighting conditions. Its enhanced low-light sensitivity and HDR capability enable the camera to capture usable image detail in dim environments and high-contrast scenes, while USB connectivity and UVC compatibility simplify integration with embedded systems, industrial PCs, and other host platforms. Designed for OEMs and system integrators, this Low Light USB Camera provides a Sony STARVIS USB Camera platform for applications that require reliable imaging when available light is limited.

The Merlin-821CRS is an 8MP 4K HDR USB Camera based on the onsemi AR0821 sensor, validated with Dynamic Real-Time ROI Auto Exposure for precise exposure control across changing scene conditions. By continuously adjusting exposure based on the selected region of interest, the camera can prioritize the subject or area that matters most rather than applying exposure correction uniformly across the entire frame. Combined with HDR imaging, H.264 video encoding, and USB 2.0 connectivity, the camera provides OEMs with a flexible imaging platform for kiosks, retail systems, machine vision, and other applications where consistent exposure and efficient video streaming are required.

The Bolt-900MGS is a 3MP Sony IMX900 Monochrome MIPI Camera featuring Quad HDR for high-dynamic-range imaging in demanding machine vision and embedded vision applications. The Sony Pregius S IMX900 sensor combines high-resolution monochrome imaging with global shutter performance, while Quad HDR enables reliable capture of detail across scenes with significant variations in brightness. With a MIPI CSI-2 interface, the camera is designed for integration with embedded platforms used in machine vision, robotics, intelligent surveillance, and automotive vision systems.

The Innova-662CRE is a 2MP NIR Camera based on the Sony STARVIS 2 IMX662 sensor, designed to deliver enhanced near-infrared sensitivity for day-and-night smart traffic monitoring. Its extended NIR response enables the camera to capture usable imagery under low-light and near-infrared illumination, supporting continuous monitoring across changing day and night conditions while retaining color imaging capabilities where lighting permits. With Gigabit Ethernet and Power over Ethernet connectivity, the camera simplifies deployment across traffic poles, intersections, highways, and other roadside infrastructure. Support for ONVIF Profiles S, T, and G enables interoperability with compatible video management, streaming, recording, and storage systems, giving traffic monitoring OEMs and ITS integrators a flexible Near Infrared Camera and PoE camera platform for 24/7 intelligent transportation applications.

The Innova-821CRS is a 4K HDR Gigabit Ethernet Camera based on the onsemi AR0821 sensor, combining 8MP high-resolution imaging, HDR performance, and PoE connectivity for smart traffic monitoring applications. With support for ONVIF Profiles S, T, and G, the camera is designed for interoperability with compatible video management, recording, and surveillance systems, simplifying integration into traffic monitoring infrastructure. The 4K HDR GigE PoE camera enables reliable imaging across varying daylight and high-contrast conditions while delivering data and power over a single network connection, making it suitable for intersections, highways, tunnels, bridges, and tolling systems.

The Bolt-544CRS is a 5MP color rolling shutter MIPI camera built on the Onsemi HyperLux LP AR0544 sensor and validated specifically for the Rockchip RK3588 platform. A camera that lists generic MIPI CSI-2 compatibility across many embedded Linux boards has not necessarily been validated on any single platform's specific CSI-2 receiver, ISP configuration, and multi-core resource allocation, and RK3588's combination of an eight-core CPU, a dedicated ISP, and a 6 TOPS NPU makes this validation gap particularly relevant for OEMs planning to run camera capture, image processing, and on-chip AI inference simultaneously on the same processor. Vadzo confirms the AR0544's full 5MP output streams cleanly through RK3588's CSI-2 receiver and ISP pipeline, and that this capture path continues to perform reliably while RK3588's NPU runs concurrent AI inference and its CPU cores handle other application logic. Output modes span full 5MP capture down to 1080p, 720p, and VGA. Designed for OEMs building edge AI vision systems, robotics, industrial inspection, and kiosk platforms on RK3588, the Bolt-544CRS gives OEMs confirmation that camera capture and RK3588's compute resources genuinely coexist rather than compete.

The Falcon-2020CRH is a 20MP Autofocus USB Camera based on the onsemi AR2020 sensor, with validated ROI Autofocus for precise focus control across different subjects and working distances. Its high-resolution imaging and voice coil motor autofocus enable the camera to maintain sharp image capture while focusing on specific regions of interest, making it suitable for barcode reading, document scanning, self-service kiosks, robotics, and other applications requiring reliable high-resolution imaging. With USB 3.2 Gen 1 connectivity and UVC support, the Falcon-2020CRH provides OEMs and system integrators with a flexible high-resolution autofocus camera platform for embedded vision applications.

The Merlin-821CRS is an 8MP color rolling shutter USB 2.0 camera built on the Onsemi AR0821 sensor and validated specifically for HDR imaging in kiosk and digital signage deployments. Kiosks, self-checkout terminals, ATMs, and ticketing machines are deliberately placed in high-visibility, high-traffic locations- lobbies, transit concourses, retail entryways- that frequently feature large windows or glass doors, and a user standing in front of such a kiosk is often backlit by exactly this daylight or storefront glass behind them. A standard dynamic range camera exposed for the kiosk's dim interior lighting renders that backlit user as a dark, featureless silhouette, losing the facial and identifying detail an interactive kiosk, self-checkout system, or ATM needs to capture. The Merlin-821CRS's onboard HDR pipeline resolves both the bright background and the comparatively dim foreground within a single exposure, giving kiosk and signage OEMs usable detail on backlit users rather than a silhouette. Output modes span full 4K capture down to 1080p and 720p. Designed for OEMs building interactive kiosks, self-checkout terminals, ATMs, ticketing machines, and digital signage, the Merlin-821CRS gives public-facing deployments the dynamic range that window-adjacent and entryway placement actually requires.

Vadzo Imaging positions the Falcon-234CGH, a 2MP global shutter autofocus USB camera built on the Onsemi AR0234 sensor. The validation program confirms stable focus and exposure performance across forklift automation and warehouse robotics deployments. The camera combines global shutter capture, onboard autofocus, and auto exposure control in a single USB 3.2 Gen1 module. This addresses the motion distortion, variable working distance, and inconsistent lighting that forklift-mounted vision systems encounter during a normal shift. Validation covered continuous runs across loading docks, storage aisles, and staging lanes, and confirmed the camera holds focus and correct exposure without manual recalibration between zones.

The Bolt-830CRH is an 8MP Autofocus HDR MIPI Camera supporting 4K imaging, based on the onsemi AR0830 sensor and validated with the NVIDIA Jetson AGX Orin platform for high-resolution embedded vision applications. Its autofocus capability enables flexible imaging across varying working distances, while HDR imaging helps capture scenes with challenging lighting conditions. With a 4-lane MIPI CSI-2 interface and validated integration with the Jetson AGX Orin, this 4K Autofocus HDR MIPI Camera provides OEMs and system integrators with a ready platform for robotics, drones, machine vision, and edge AI applications.

The Falcon-821CRH is an 8MP color rolling shutter USB 3.2 Gen1 camera built on the Onsemi AR0821 sensor, combining voice coil motor autofocus with high dynamic range imaging in a single module. Most camera products solve one of these two problems at a time: a fixed-focus HDR camera holds exposure latitude but only at one calibrated distance, while a standard dynamic range autofocus camera adjusts focus but loses detail the moment a scene contains both bright and shadowed regions. The Falcon-821CRH addresses both simultaneously, holding focus across a wide range of object distances while its HDR pipeline resolves high-contrast scenes at whatever distance the lens is currently focused on. Output modes span full 4K capture down to 1080p and 720p, with autofocus control exposed through the camera's standard interface. Designed for OEMs building barcode readers, document scanners, self-service kiosks, robotics, and machine vision systems, the Falcon-821CRH removes the assumption that an integrator must choose between focus flexibility and dynamic range.

Vadzo Imaging has completed platform validation of the Bolt-821CRS, an 8MP color MIPI CSI-2 camera built on the Onsemi AR0821 sensor, confirming stable capture and driver behavior when interfaced directly with Rockchip RV1126 vision processor boards. The camera pairs an 8MP color sensor with on-chip HDR and a native MIPI CSI-2 output, removing the USB bridge chip that many embedded camera modules still rely on. Validation covered continuous streaming, resolution switching, and exposure stability across RV1126-based carrier boards used for edge AI and embedded vision development.

Vadzo Imaging has positioned the Innova-234CGE, a 2MP global shutter GigE camera built on the Onsemi AR0234 sensor, for digital pathology and clinical laboratory imaging systems. The camera pairs global shutter capture with a native GigE Vision interface, addressing the motion artifact, cable length, and stage synchronization requirements that whole slide scanning and microscopy platforms depend on. This positioning reflects growing demand from pathology instrument builders for a camera that holds a moving slide image steady, connects over standard Ethernet cabling across a lab bench, and synchronizes precisely with a motorized microscope stage.

Built for surveillance, security, and industrial vision applications that demand exceptional performance in challenging lighting conditions, this 2MP Ultra-Low Light GigE Camera pairs the Sony IMX662 STARVIS 2 sensor with a high-performance ISP and ONVIF-compliant GigE Vision connectivity, giving integrators a single platform that delivers both superior image quality and seamless network integration for modern video management systems.

The Merlin-821CRS is an 8MP color rolling shutter USB 2.0 camera built on the Onsemi AR0821 sensor and validated specifically for real-time 4K video streaming on kiosk and digital signage hardware. USB 2.0's bandwidth ceiling cannot carry raw or lightly compressed 4K video at a usable frame rate, which means a camera claiming 4K resolution over this interface produces choppy, unusable video unless the sensor's output is compressed substantially before it ever reaches the USB connection. The Merlin-821CRS resolves this with onboard hardware compression that fits genuinely smooth 4K HDR video within USB 2.0's real throughput ceiling, and its dual endpoint streaming lets one compressed feed serve the kiosk's on-screen display while a second stream simultaneously supports an audience analytics or monitoring application. Output modes span full 4K capture down to 1080p and 720p. Designed for OEMs building interactive kiosks, digital signage, vending machines, and self-service terminals, the Merlin-821CRS gives USB 2.0-based products the 4K streaming performance their host hardware was never expected to carry unprocessed.

The Bolt-2020CRS is a 20MP color rolling shutter MIPI camera built on the Onsemi HyperLux LP AR2020 sensor and validated specifically for the NVIDIA Jetson AGX Orin platform. A sensor's resolution figure on a datasheet is not the same as the resolution an application actually receives once that sensor is paired with a specific host platform's CSI-2 receiver and hardware ISP pipeline, and a camera validated only for basic capture provides no assurance that the full 20MP frame reaches the application rather than being silently cropped or binned down to a lower effective resolution. Vadzo confirms the AR2020's complete 20MP pixel array streams through Jetson AGX Orin's CSI-2 receiver and ISP at practical frame rates, including validated behavior supporting multiple simultaneous camera streams for NVR and multi-camera configurations. Output modes span full 20MP capture down to 4K, 1080p, and 720p. Designed for OEMs building edge AI vision systems, multi-camera NVR products, robotics, and industrial inspection platforms on Jetson AGX Orin, the Bolt-2020CRS gives OEMs confirmation that the resolution they specified is the resolution their application actually receives.

The Innova-662CRE is a 2MP color rolling shutter GigE Vision camera built on the Sony STARVIS 2 IMX662 sensor and engineered for smart traffic monitoring deployments. Gigabit Ethernet with Power over Ethernet lets a single Cat5e or Cat6 cable carry both power and data up to one hundred meters from a roadside camera to the nearest network cabinet, removing the short cable run limitation that makes USB and MIPI camera products impractical for pole-mounted traffic infrastructure. The STARVIS 2 sensor's wide dynamic range handles the backlit and high-contrast scenes common at intersections, tunnel entrances, and toll booths, resolving vehicle and license plate detail in both bright sky and shadowed roadway within the same frame. Native GigE Vision compliance means the camera integrates with standard machine vision software without a proprietary capture card. Designed for OEMs and system integrators building traffic monitoring, tunnel, bridge, and toll infrastructure, the Innova-662CRE gives traffic camera deployments the cable distance and dynamic range that roadway conditions demand.

The Falcon-234CGH is a 2MP color global shutter Autofocus USB camera built on the Onsemi AR0234 sensor and paired with voice coil motor autofocus, a combination positioned specifically for forklift automation. A forklift presents two imaging challenges at once that most camera products address separately at best. The vehicle itself is in continuous motion through the warehouse, which a rolling shutter sensor renders as geometric skew the instant the forklift moves, and the working distance between the camera and a fork, pallet, or rack opening changes constantly as forks raise, lower, and approach different rack positions, which a fixed focus lens cannot follow. Global shutter exposure captures every pixel simultaneously regardless of vehicle motion, while continuous autofocus holds the fork or load in sharp focus across the full range of working distances a lift cycle presents. Output modes span full 2MP capture down to 1080p and 720p. Designed for OEMs building forklift vision, pallet detection, load sensing, and collision avoidance systems, the Falcon-234CGH gives warehouse automation the motion integrity and focus accuracy that a moving, height-adjustable vehicle actually requires.

The Bolt-821CRS is an 8MP color MIPI camera built on the Onsemi AR0821 sensor and validated specifically for the NVIDIA Jetson AGX Orin platform. A camera that merely produces a raw Bayer frame over MIPI CSI-2 is not the same as a camera whose HDR output is properly calibrated for NVIDIA's Argus camera framework, and most AI applications on Jetson AGX Orin route through Argus rather than bypassing it. Vadzo confirms the complete pipeline from the AR0821 sensor through Jetson AGX Orin's hardware ISP and Argus daemon, including validated ISP tuning specific to the sensor's HDR mode, giving OEMs a camera that delivers properly tone-mapped high dynamic range video through the same framework their GStreamer and DeepStream pipelines already depend on. Output modes span full 4K capture down to 1080p and 720p. Designed for OEMs building edge AI vision systems, robotics, drones, and industrial inspection products on Jetson AGX Orin, the Bolt-821CRS removes the gap between a camera that merely captures frames and one that is actually ready for NVIDIA's camera software stack.

Built for machine vision, industrial inspection, quality control, and automation applications that demand high-resolution imaging with precise focus control and reliable industrial networking, this 4K Autofocus GigE Camera pairs the Onsemi AR1335 sensor's genuine 13MP resolution with autofocus precision over low-latency GigE Vision streaming, giving vision system integrators and equipment manufacturers professional imaging quality regardless of working distance or production environment.

The Falcon-1335MRS is a 13MP Monochrome USB Camera based on the onsemi AR1335 sensor with 1.1µm pixels, designed for low-light imaging in medical and life sciences applications. Its monochrome architecture and back-side illuminated sensor provide high-sensitivity imaging for microscopy, laboratory automation, diagnostic instrumentation, and clinical imaging systems where fine detail must be captured under controlled or limited lighting. With USB 3.2 Gen 1 connectivity, native UVC support, and multiple resolution output modes including 13MP and 4K, the camera provides OEMs and system integrators with a flexible imaging platform for medical and scientific equipment.

The Bolt-830CRH is an 8MP color rolling shutter MIPI camera built on the Onsemi HyperLux LP AR0830 sensor and validated specifically for the Rockchip RK3588 processor. OEMs choosing RK3588 over a lower-tier Rockchip platform are usually doing so because their application needs meaningfully more compute headroom, whether that means running a heavier AI inference model, aggregating several camera streams into a single NVR pipeline, or handling both HDR tone mapping and autofocus control without either process starving the other of ISP or NPU cycles. Vadzo confirms the AR0830's staggered HDR pipeline and voice coil motor autofocus operate correctly on RK3588's higher-performance ISP and NPU, including validated behavior under multi-stream configurations that a lower-tier platform could not sustain at the same resolution and frame rate. Output modes span full 4K capture down to 1080p and 720p. Designed for OEMs building edge AI vision systems, multi-camera NVR products, robotics, and industrial inspection platforms on Rockchip silicon, the Bolt-830CRH gives RK3588-based products the validated headroom their higher-performance platform choice was meant to provide.

The Merlin-821CRS is an 8MP USB camera delivering 4K HDR imaging over USB 2.0, built around the onsemi AR0821 sensor with Auto White Balance for consistent color reproduction across changing lighting conditions. Designed for print inspection, textile inspection, color matching, photography, and other imaging applications, this 4K USB 2.0 camera combines high-resolution capture, HDR performance, and automatic white balance in a compact UVC camera platform for easy integration.

The Bolt-1335CRO is a 13MP color rolling shutter MIPI camera built on the Onsemi AR1335 sensor and validated specifically for the Rockchip RV1126 processor with gyro-driven optical image stabilization. Handheld field devices, wearable camera systems, and small drones share a problem that focus and exposure tuning cannot solve on their own: the camera itself is in continuous motion, and that motion introduces blur that digital stabilization can only crop and warp after the fact rather than prevent. Optical image stabilization physically counteracts that motion within the exposure window itself, so the frame reaching the RV1126's NPU is sharp before any software correction runs, not after. Vadzo confirms the complete MIPI CSI-2 pad chain from the AR1335 sensor through the RV1126's camera subsystem, including validated driver support for the OIS actuator alongside standard capture control. Designed for OEMs building handheld field service devices, wearable and body-worn camera products, and stabilized drone payloads on Rockchip silicon, the Bolt-1335CRO gives motion-prone deployments the stabilized capture that edge AI accuracy depends on.

The Merlin-662CRS is an Ultra Low Light USB Camera based on the Sony IMX662 STARVIS 2 sensor, delivering HDR imaging and enhanced near-infrared sensitivity for smart surveillance and security applications. As an IMX662 USB UVC Camera, it provides plug-and-play USB connectivity for easy integration with surveillance systems, edge computing platforms, and intelligent video applications, enabling reliable imaging across low-light, high-contrast, and infrared-assisted environments.

The Innova-234MGS is a 2MP Monochrome Global Shutter Gigabit Ethernet Camera based on the onsemi AR0234 sensor, designed for industrial inspection, machine vision, and factory automation applications. Its global shutter architecture enables accurate image capture of moving objects without the motion distortion associated with rolling shutter cameras, while the monochrome sensor provides high-contrast imaging for defect detection, dimensional inspection, and code reading. Gigabit Ethernet connectivity with PoE enables flexible deployment over a single network cable, while ONVIF support facilitates integration with compatible video management and industrial imaging systems.

Built for high-speed sorting, inspection, robotics, and barcode reading applications that move too quickly for a standard single-exposure sensor to reliably capture, this camera pairs the Sony Pregius S IMX900 monochrome sensor with Quad Shutter Control over USB 3.0, giving integrators genuine rapid, multi-exposure readout without the motion distortion a rolling shutter sensor would introduce at the same speed.

The Innova-821CRS is a 4K Gigabit Ethernet camera featuring the 8MP Onsemi AR0821 color rolling shutter sensor, HDR imaging, and validated IEEE 1588 PTP synchronization. As a PTP synchronization camera, it enables multiple cameras on the same Ethernet network to align their timing to a common reference with sub-microsecond precision, supporting synchronized multi-camera imaging without dedicated trigger wiring. The 4K HDR GigE camera also supports ONVIF and GenICam, enabling integration with standard machine vision software for robotics, industrial inspection, metrology, and other applications requiring synchronized high-resolution imaging.

The Bolt-2020CRS is a 20MP Color MIPI camera based on the onsemi AR2020 sensor, validated with the Rockchip RK3588 processor for high-resolution imaging and embedded vision applications. The validated MIPI CSI-2 integration provides OEMs with a ready camera platform for RK3588-based robotics, edge AI, industrial vision, kiosks, and other high-performance embedded systems.

The Merlin-291CRS is a 2MP color rolling shutter USB camera built on the Sony IMX291 sensor and positioned specifically for patient monitoring deployments. Overnight monitoring depends on capturing usable video in the dim or near-dark conditions patients need for rest, and the IMX291's low-light pixel architecture resolves that video without supplemental illumination that can disturb sleep or feel invasive at the bedside. The camera streams two independent video feeds from a single USB connection, one suited to continuous live viewing at a nurse station and another suited to higher quality local recording for documentation, both without saturating a hospital network. Native USB 2.0 UVC connectivity means the camera enumerates without proprietary drivers on the desktop and embedded platforms hospital IT departments already deploy. Designed for OEMs and system integrators building patient monitoring, nurse call, and care facility products, the Merlin-291CRS gives bedside deployments the low light performance and streaming flexibility that continuous patient observation actually requires.

The Bolt-1335CRA is a 13MP color rolling shutter MIPI camera built on the Onsemi AR1335 sensor and validated specifically for the Rockchip RV1126 processor. A voice coil motor autofocus lens gives edge AI vision systems a working distance that adjusts to the application, while the RV1126's integrated neural processing unit runs on-device inference directly adjacent to the camera pipeline without a separate compute module. Vadzo's validation confirms the complete MIPI CSI-2 pad chain from the AR1335 sensor through the RV1126's RKISP hardware image processor, giving OEMs a proven hardware and driver starting point rather than an open-ended integration project. Output modes span full 13MP capture down to 1080p and 720p, with autofocus control exposed through the platform's standard camera framework. Designed for OEMs building edge AI camera systems, robotics, kiosks, drones, and industrial vision systems on Rockchip silicon, the Bolt-1335CRA gives engineering teams a camera platform that stays in focus and feeds a validated inference pipeline at the same time.